Installation Instructions
Garage Door Opener Radio Controls
Model 5030 (300 mHz) \ 5032 (310 mHz) Three Button Transmitters
WARNING:
· Disconnect
operator power before any installation or repair
· Always wear
safety glasses
Your
Digi-Code radio controls are designed specifically to remotely control a garage
door opener from within an automobile and to give years of trouble free service
without adjustment. Because all radio
controls are set with the even numbered switches in the “ON” position when they
leave the factory, it is recommended that a different code be selected and set
at the time of installation. Please
refer to the “Setting the Code Switches” section for instructions. The radio
frequency (RF) portion of the controls, however, are tuned to standard
frequencies and are thoroughly tested at the factory. This permits the addition
or replacement of either the transmitter or the receiver by specifying the
Model number and the RF frequency designated on the identification label. RF
adjustments are not needed nor should any be attempted.
SECTION #1
SETTING
THE CODE SWITCHES
On
the transmitter the entire front lower half of the case ( “ the battery hatch”
) is removeable. Use a coin or the curved end of the visor clip to disengage
the lower half of the transmitter front. This will expose both the code switch
and the battery compartment.
(
SEE FIGURE #1 )
Figure
#1
Once
you have removed the battery hatch, locate the “CODE SWITCHES” above the
battery. As shown above, the dual buttons are controlled by the right hand
switch and the single button is controlled by the left hand switch.
Before setting the
receiver code switches, you will need to set the transmitter code switches on
your model 5030 or 5032. We strongly suggest that you change the code from the
factory setting to provide security for your own system, and to eliminate
interference with neighboring systems.
SETTING THE DUAL BUTTON CODE SWITCH
Set code switch positions
1 through 9 to your personal code scheme ( THE 10TH POSITION SWITCH MUST BE SET IN THE CLOSED
POSITION “ON”), (Note: The switch
is in the “on” position when it is depressed toward the number.). We strongly urge that several coding schemes be
avoided: ALL ON; 2,4,6,8,10, ON. These positions are similar to our or other
manufacturers test positions, or are frequently used.
SETTING RECEIVER #1 (WORKS WITH LEFT DUAL BUTTON )
Set your receiver code
switch positions 1 through 9 to match the dual button code switch. Then
make sure that the 10th position switch on receiver #1 is set in the
closed position “ON”. The left dual button on
the transmitter should now operate this receiver.
SETTING RECEIVER #2 (WORKS WITH RIGHT DUAL BUTTON )
Set the receiver code
switch positions 1 through 9 to match the dual button code switch. Then
make sure that the 10th position switch on receiver #2 is set in the
open position “OFF”. The right button on the
transmitter should now operate this receiver.
Once the codes have been set, check operation.
SETTING THE SINGLE BUTTON CODE
SWITCH
Set code switch positions
1 through 10 to your personal code scheme, any combination of “on” or “off”
positions can be selected (Note:
The switch is in the “on” position when it is depressed toward the number.). We strongly urge that several coding schemes be
avoided: ALL ON; 2,4,6,8,10, ON. These positions are similar to our or other
manufacturers test positions, or are frequently used.
SETTING RECEIVER – TO WORK WITH SINGLE BUTTON
Set the receiver code switches to match the code settings you entered for the single button switch in the transmitter, being sure both are set the same since a different setting of just one switch will prevent operation.
Once the three codes have been set, check operation and reinsert the hatch.
SECTION #2
SETTING THE TRANSMITTER CODE SWITCHES –TO WORK WITH EXISTING STANLEY GARAGE DOOR OPENERS ( Model 5032 – ONLY ).
Set
the transmitter using “SETTING
THE DUAL BUTTON CODE SWITCH” AND “SETTING THE SINGLE BUTTON CODE SWITCH” instructions from
section #1 above.
Set the first garage door
opener using “SETTING RECEIVER #1 (WORKS WITH LEFT DUAL BUTTON) “ instructions from section #1 above.
Set the second garage
door opener using “SETTING RECEIVER #2 (WORKS WITH RIGHT DUAL BUTTON )” instructions from section #1 above.
Set the third garage door
opener using “SETTING RECEIVER – TO WORK WITH SINGLE BUTTON ” instructions from section #1 above.
SECTION #3
TRANSMITTER BATTERY REPLACEMENT
The battery in the
transmitter can be checked or changed by removing the front lower half of the
transmitter. Use a coin or the curved end of the visor clip to disengage the
lower half of the transmitter front. This will expose the battery compartment.
Replacement battery must be a 9-volt.
TO REPLACE OR ADD A SET
A replacement or new
transmitter or receiver may be purchased by specifying the Model Number and the
RF frequency designated on the serial tag label. The RF frequency is set at the
factory and must not be adjusted in the field. The digital code can be matched
to the companion receiver or transmitter by following the “setting” procedures
above.
OPERATIONAL CHECK
To check operation, move
back about 50 feet and press the transmitter button. Operation should be
reliable at this distance but environment and location of both the transmitter
and receiver will effect the range. Try different mounting locations and
positions in the vehicle. If operation is still undesirable, the problem may be
isolated by:
1.
Checking the door
operator. If the door will not open when the wall button is
pressed,
the problem is likely to be the operator. If the door will open by pressing
the
wall button, but not when the radio control button is pressed, the problem is
probably
in the radios.
2.
Replacing the
transmitter battery.
If, after performing the
above operational checks, the controls still do not function, they should be
returned to your dealer for repair or replacement.
WARRANTY
All Digi-Code door
related products carry an eighteen (18) month warranty against defects in
workmanship or material. This warranty begins at the date of manufacture, for
eighteen months. Digi-Code warrantees our product only to our authorized
dealers and distributors, and not to the end customer. If you have any
questions about our warranty, please ask your dealer to determine the nature
and scope of their warranty. Digi-Code does not assume, and is not responsible
for, any real or consequential damages from claims against the performance of
our product, nor is it liable for any costs related to the loss of life, property,
or revenue. Further, Digi-Code is in no way responsible for installation of our
product, and will assume no cost related to reinstallation or removal.
Digi-Code’s warranty is in lieu of all other warrantees, expressed, or implied.
CAUTION: Any
changes or modifications in intentional or unintentional radiators which are
not expressly approved by Digi-Code Inc. could void the users authority to
operate this equipment. This applies to intentional and unintentional radiators
certified per part 15 of the FCC rules and regulations.
DIGI-CODE, INC.
307 ROBBINS DR. · TROY,
MICHIGAN 48083
(248) 589-3645
Part # 72-5030A